Rite-ride 2565 User Manual download pdf

2565

02-14

INSTALLATION INSTRUCTIONS

Congratulations—your new Air Helper Springs are quality

products capable of improving the handling and comfort

of your vehicle. As with all products, proper installation is

the key to obtaining all of the benets your kit is capable

of delivering. Please take a few minutes to read through

the instructions to identify the components and learn

where and how they are used. It is a good idea to start by

comparing the parts in your kit with the parts list below.

The heart of the air helper spring kit is, of course, the

air springs. Remember that the air helper springs must

ex and expand during operation, so be sure that there

is enough clearance to do so without rubbing against any

other part of the vehicle.

Be sure to take all applicable safety precautions

during the installation of the kit. The instructions listed

in this brochure and the illustrations all show the left,

or driver’s side of the vehicle. To install the right side

assembly simply follow the same procedures.

Your kit includes separate ination valves and air

lines for each air helper spring. This will allow you to

level your vehicle from side to side as well as from front

to back. If you would rather have a single valve ination

system, your dealer can supply the required “T” tting.

IMPORTANT!

For your safety and to prevent possible damage

to your vehicle, do not exceed the maximum load

recommended by the vehicle manufacturer (GVWR).

Although your Air Helper Springs are rated at a maximum

ination pressure of 100 psi, this pressure may allow you

to carry too great a load on some vehicles. It is best to

have your vehicle weighed once it is completely loaded

and compare that weight to the maximum allowed. Check

your vehicle owner’s manual or data plate on driver’s side

door for maximum loads listed for your vehicle.

When inating your Air Helper Springs, add air pres-

sure in small quantities, checking pressure frequently

during ination. The air spring requires much less air

volume than a tire and, therefore, inates much quicker.

WARNING:

Do not inate this assembly when it is

unrestricted. The assembly must be restricted

by the suspension or other adequate

structure. Do not inate beyond 100 psi

Improper use or over ination may cause

property damage or severe personal injury.

AIR SPRING 9055 2

UPPER BRACKET 5771 2

LEFT FRAME BRACKET 5701 1

RIGHT FRAME BRACKET 5700 1

LEFT LOWER BRACKET 5791 1

RIGHT LOWER BRACKET 5790 1

FRAME HOLE BRACKET 5660 4

BAIL CLAMP 4.5 X 2.5 X 2.0 3410 4

AIR LINE TUBING 18 FT. 1

INFLATION VALVE 3032 2

ELBOW FITTING 3048 2

3/8"-16 FLANGE LOCK NUT 16

3/8"-16 X 1" HEX HEAD BOLT 12

3/8"-16 X 1/2" FLANGE BOLT 4

M10 X 20 MM BOLT 2

5/16" FLAT WASHER 4

THERMAL SLEEVE 2

NYLON TIE STRAP 6

CAUTION TAG 2

PARTS LIST

BOLT PACK (A21-760-2565)

1 2 3 4

WARNING: 1
Figure “A” 2

Summary of Contents

Page 1 - WARNING:

2565 02-14INSTALLATION INSTRUCTIONSCongratulations—your new Air Helper Springs are quality products capable of improving the handling and comfort of y

Page 2 - Figure “A”

BAIL CLAMP(3410)3/8"-16FLANGELOCK NUTS3/8"-16FLANGELOCK NUTSM10 X 1.5 X 20MMHEX BOLTLOWERBRACKET(5792)AIRSPRING(6781)FRAMEINSERT FRAME HOLEB

Page 3

STEP 1 — PREPARE THE VEHICLEWith the vehicle on a solid, level surface, chock the front wheels. Raise the vehicle by the rear axle and set on jack sta

Page 4

the tube. If a leak is detected where the tting screws into the spring, screw the tting into the air spring until the leak stops. Reinstall the tubi

Comments to this Manuals

No comments

Rite-ride 2565 User Manual

Browse online or download User Manual for For the car Rite-ride 2565. Rite-Ride 2565 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Rite-ride 2565